Name
Shemyakin Alexander Vladimirovich
Scholastic degree
•
Academic rank
associated professor
Honorary rank
—
Organization, job position
Ryazan State Agrotechnological University named after P.A. Kostychev
Web site url
—
Articles count: 9
The carried out analysis studies the influence of
various factors on the preservation of
agricultural products and shows that it is largely
determined by design features of machinery and
technological methods of use. The efficiency of
agricultural and mobile trailer machines has
been forming by service and storage. Low
quality of work associated with the storage of
agricultural machines is conditioned by the fact
that the lack of financial capacity of rural
producers on acquisitions of modern equipment
and materials for carrying out the preparation of
for long storage, and also the construction of
modern agricultural machinery storage sites. If
a car can be fully or partially protected from the
solar radiation, rain and snow, simply by
removing it in the room, under a canopy or
covered with a protective cover, by the
formation of condensation on the surface of the
machine units and parts these ways to protect
do not work. Enhancing of preservation of
agricultural machinery is possible when
protecting the vehicles from atmospheric
precipitation in the form of snow and rain,
influence of solar radiation, and also due to the
change heat exchange processes of the machine with the environment that prevents the
formation of moisture condensate on its surface,
ie. we have to create conditions when cooling
rate at which the surface of the machine would
be equal to or less the rate of cooling air. This is
possible through the use of a special design,
which would prevent the intense heat radiation
of the machine into the environment, ie, would
reflect heat rays using its surface and return
them to its surface and thus fulfill the role of the
heat shield
At the present time there is a problem in storage
of agriculture machine-tractor park, because when
operating of agricultural machinery parts thereof
are covered by contamination. The most heavily
becomes dirty machinery working in the toughest
conditions. Pollution promotes decrease the
operational reliability, accelerating of corrosion
and aging, reduce the quality of maintenance
service and performance technique. One of the
number of important factors when setting
technique for storage is the clearing of by of
various types pollution, because the during
storage of cleaned surfaces, components and parts
are subjected still greater destruction and
corrosion. Removal of various kinds of pollution
is an important technological process which has a
significant impact on the preservation of
appliances, performance of work, the quality of
the repair and maintenance of cars, culture,
production and human health. The article contains
a classification of contamination depending on the
difficulty of their removal and density, basic
information on techniques and devices for
purification of units and parts of agricultural
machines, as well as on substances used for this.
We have reviewed bombardment of surfaces with
contaminated carbon dioxide ice particles that
leads to its full destruction. We have improved technology and created a universal device and the
experimental plant for cleaning parts and
assemblies prior to storage, which are not only
inferior, but also in the majority superior to
technical and economic performance of existing
analogues
One of the promising directions of development of
agriculture of the Russian Federation is to increase
the production, improve the quality and decrease the
cost of potato cultivation. Annual cleaning is one of
the most intense and costly in transport and
technological processes. Potatoes - blending high
culture and very picky about cleaning. The highest
yields and income from potato production get where
embedded technology to optimize energy and labor
costs. The main (though not only) the special
technical means used during machine harvesting
potatoes, are potato harvesters. The main problem
when cleaning is a problem of balancing conflicting
requirements to the process and possibilities of
agricultural machinery. Including increasing the
purity of the tubers in the container with one hand,
minimization of losses and damages of tubers on the
other hand, when the performance of equipment. In
this article we propose a circuit-design solution
separating the working body of the potato harvester
that allow for cleaning to significantly reduce the
amount of traumatized potatoes in the process of
separating soil and vegetable impurities, creating the
preconditions for the elimination of damage to the
tubers on the hard side of the working bodies of
harvesting machines. Informed choice and timely use
of plug-in modules (separating working bodies) in
modern potato harvesting machines at work in
specific climatic conditions allows them to fully
match the list of regulated agronomic requirements.
Thus, the creation of new science-based technical
solutions for a separation of the organs of potato
harvesters is an actual scientific-technical task, which
makes a significant contribution to the development
of the country
Potato is cultivated in 130 countries on an area of over
18 million hectares; it annually gives more than 300
million tons of tubers. The share of the Russian
Federation accounts is about 11% ... 14% of total
production. The resulting potatoes consumed in food, animal feed, technical purposes, seed fund. According
to the Ministry of agriculture of Russia, the largest
number of potatoes in our country (89 %) is produced in
peasant farms and personal farms of citizens, the area of
cultivation of which make up about 2.7 million hectares.
At such farms for the harvest, they use mainly potatodiggers,
followed by selection of crops manually. The
use of diggers in small areas of planting is more costefficiently
in relation to the harvesting combine. In
addition, the parameters requested for ATT to damage
potatoes when harvesting with the diggers (3%) are
higher than during harvesting by combine harvester
(5%). As practice shows, for the use of cleaning units,
even under optimal harvesting conditions in the hopper
of the combine, there are soil and vegetable impurities.
There are many different devices intended to localize
the problem. Based on the foregoing, we can conclude
that it is necessary to pay considerable attention to the
quality of work of excavating working bodies, because
it affects the productivity of the functioning of the
whole machine. Currently, there are widespread potato
aggregates with the receiving part, equipped with side
disks, spaced along the edges of the plowshares. The
disks cut off the raised layer of soil from between the
rows. This entails improving the performance of the
potato harvester. The most efficient and economical
from the point of view of energy consumption, is the
work of passive disks with hooks. The quality of potato
harvesters depends on the design and performance of
excavating bodies. The proposed design solution for an
excavating body increases the productivity of harvesting
machines
The article presents a technical diagnostics of a car as a complex of goals and tasks connected with
trouble-shooting of mechanisms and systems in
order to eliminate them. We have considered the
stages of computer diagnostics of different
automobile systems such as diagnosing the engine,
the brake system, steering and suspension. We have
analyzed their components, the ways of troubleshooting
and elimination recommendations. The
article presents the main troubles transferred from
the electronic control unit. The article also presents
the stages of diagnosing the engine including
external examination, listening to abnormal noises,
checking the operating fluids and the engine
management system, diagnosing the basic engine
systems and checking the cylinders being filled.
The article contains the list of main troubles and
their reasons. One can also see diagnosing the brake
system, its defects and remedies. The article
presents diagnostics and repair of the suspender and
graphics describing the check of the dismantled
shock strut at the stand and tests of the shock strut
without being dismantled. We have analyzed
computer diagnostics and the problems it solves
Material and technical resources form a large part of the
costs in agricultural production and determine the level
of intensity of agriculture, productivity and
competitiveness of the industry. The most important
role in agricultural production is played by transport
operation, from productivity and quality of which
directly depends the volume and the grade of final
products. More preferable is tractor transport,
particularly for on-farm transport, taking into account
the impact of navigation systems on the ground.
Continuous growth in the saturation of tractors carried
out around the world, improves the performance of
tractor transport aggregate by increasing their capacity and speed, either on the road or in the field. However, if
you increase the saturation of tractors, it encounters
problems related to the deterioration of the
controllability of the tractor and transport unit. The
reduced controllability leads to an increase of damage to
transported agricultural products owing to increased
oscillatory processes in the system of "road – trailer –
tractor – operator" when driving on-farm trails,
deteriorating the smoothness and braking properties.
Especially sharp these questions relate to transportation
of easy-to-damage agricultural products at farm
transportation. The feature of data traffic lies in the
sharp drop in grade products (products receive
numerous mechanical damages, deteriorating its quality,
and lose marketability and accordingly reduced its cost).
Influence on fruit and vegetable products of unfavorable
factors can lead not only to a dramatic loss of quality at
the time of transportation, but also reduce the resistance
during further storage. To solve the problems emerging
when increasing the saturation of tractors, we have
proposed devices, allowing reducing negative impact on
the production of elevated oscillatory processes, to
increase the permeability and straightness of movement
of tractor-transport unit
In agriculture the issue of enhancing the
efficiency of operation of internal combustion
engines (ICE), reducing the costs of
maintenance (TO) and repairing (TP) fuel
supply apparatus (TA) using the improvement
of methods and means of diagnosis is a topical
in connection with the aging rolling stock
farming and lack of investment. Analysis of the
known TA diesel engine vehicles systems
showed that the most widespread system is the
divided type with multiplunger high pressure
fuel pump (fuel pump), while the methods of its
diagnosing are laborious, they require partial
disassembly and have insufficient accuracy.
The mathematical models that characterize the
work of a high-pressure fuel pump (fuel pump)
use a large number of parameters that
significantly affect the quality of dynamics of
the change of pressure values of diesel fuel.
However, in the materials of previously
published articles there were no issues
considered assessing the extent of the
quantitative impact, performance and features
change in the sensitivity settings of the
mathematical models on the simulation results,
there are no recommendations on the degree of
sensitivity and importance of each of the
parameters. For a more accurate diagnosis of
the fuel supply apparatus of a diesel engine it is
advisable to use several methods of diagnosing.
The article substantiates development of a
mathematical model of a high-pressure fuel
pump based on the analysis of modern methods
of diagnosing of fuel equipment for autotractor
diesel engines
Potato has been and remains one of the five world's
most important crops. For nearly two hundred years
potato in Russia is the "second bread". This is one of
the so-called social products. Over the past 20 - 25
years of potato farming in our country, there have been
significant changes, both positive and negative. Today,
potatoes are grown in different soil and climatic
conditions in more than one hundred countries around
the world, including the desert oasis and beyond the
polar circle. Potato cultivation Center recently has
moved to Asia. In our time, the leaders of potato
production are China, Russia, India, the US and
Ukraine. Over the past few decades the number of
produced potatoes has increased by 41% and the area under potato planting only 9.5%. From the above data
it is clear that the world potato economy in recent
years has got significant changes, indicating that the
timeliness and relevance of the material in this article
is true