Name
Bоrychev Sergey Nikоlaevich
Scholastic degree
—
Academic rank
—
Honorary rank
—
Organization, job position
Ryazan State Agrotechnological University named after P.A. Kostychev
Web site url
—
Articles count: 33
In recent years, in many countries around the
world, much attention is paid to the issues of
ensuring of rational use of energy resources,
due to a number of objective factors, chief
among which are: the lack of own energy
resources to meet domestic energy needs; the
sharp increase in the cost of production and the
production of energy resources; further growth
in energy needs; the presence of large potential
opportunities to reduce unproductive losses of
fuel and energy. In the world, the challenge
now is to ensure a gradual but steady transfer of
the economy on energy saving way of
development. To achieve the goal of reducing
energy costs we might use two ways: firstly, the
widespread introduction of energy saving
technologies, and secondly, the reduction of
material production, improving its quality and
service. In agriculture, the improvement of the
technological process can be carried out using
new tillage methods, improving the
organization of production and tools. Further
development of mechanization in agriculture
will contribute to further growth of
electrification in the agricultural sector, which
will significantly reduce the use of the most
expensive and limited energy resources. The
article offers a technique of the estimation of
the efficiency of consumption of energy in
agricultural production. In order to compare the
efficiency of machines in the cultivation and
harvesting of potatoes, there was conducted an
energy assessment of the operations of modern
technology. As variables, there were
investigated different operation modes of the
machine: working speed and working width,
depth of stroke of the working bodies. In the
process of evaluating energy operations,
modern technology to prepare the soil for
planting potatoes was determined humidity,
mechanical composition and soil type. As a
main factor in the analysis of technological
methods, we have taken the overall specific
energy consumption and specific energy
consumption for the digging below tuber
formation. Analysis of theoretical researches of
agricultural machinery has led to the conclusion
that the energy cost of implementing the
technological process in the machines of
different designs varies
While mechanical harvesting of potatoes, about
20-40% of the tubers get damages. Dynamic
loads, injuries of the tubers, causing internal
damage – which is browning of the flesh of the tuber, which occurs in the process of its storage.
At the same time, ways to express control of
damage to potato tubers will allow both
reducing damage during harvest, and promptly
sending damaged potatoes for recycling before
the results of mechanical stress for the tubers
during harvesting. The definition of internal
damage to the potatoes is possible because of
the analysis of the different elasticity of the
tissues of damaged and undamaged tubers. The
value of overpressure of the device is chosen
such way that during deformation of tubers
there mainly has been compression of the
damaged tissues of the tuber, with the least
turgor. The degree of damage of samples of
tubers is determined by the ratio of the volume
of damaged tissues of tubers to the total volume
of the sample. We have given the mechanical
properties of tissues of tubers, fruits and root
vegetables, their structure, dimensional
characteristics, it can be assumed that the use of
this method of determining internal damage
possible for apples, carrots, beets and harvest of
other crops. Use of damage control will enable
timely identification of hidden damage and
make it possible to eliminate their causes,
which lead to increase loss products
In the world, recycling processes have recently
become more common in order to save material and
energy resources. Currently, in connection with the
level of motorization, there grew a problem of
recycling waste tires and their elements which is of great importance for many regions of the country.
Decommissioning worn tires is a source of
environmental pollution, bearing the prolonged
character; they are not a subject to biological
destruction and require constant increase of storage
facilities. There is a continuous accumulation of used
tires and we can recycle only about 20% of their
amount. Worn tires represent very large-capacity
products of polymer-containing waste, virtually
resistant to natural degradation. Therefore, the
problem of processing and secondary use, emerged
from the operation of tires is of great economic and
environmental significance. However, the worn tires
are a source of valuable secondary raw materials:
rubber, soot (essentially pure carbon), metal and
synthetic cord. 90% of all waste of rubber are tires
and represent a vast reserve of raw materials. In the
emerging in the industry nonrenew- material
resources the efficient use of secondary raw materials
is of great importance. There are improved
technologies for processing rubber goods, and the
equipment used for it
Fruit harvesting is the final and decisive
operation in the general work plan for growing
fruit, which largely determines the qualitative
and quantitative indicators of production and
economy of industry in general. Increasing
productivity by improving the safety of fruits
and vegetables is a priority and not an easy task.
For example, the use of cleaning technologies
with the use of machinery for harvesting of
apples by shaking can significantly reduce the
time of gathering fruit compared to hand
harvesting. This technology may be applicable,
if the fruit is grown for the manufacture of
juices, jams, etc. Currently, in several European
countries and in the USA, they widely use fruit
harvesting platforms and machines. The leader
in the production of fruit harvesting platforms is
Italy. To reduce the damage to fruit in
agriculture, the analysis of the traumatic factors
is of great importance, with the analysis of
available machines and their subsequent
modernization with the aim of improving the
reliability and quality of harvesting and
transport process, taking into account of the
algorithm for solving these problems, the
creation of new varieties of fruits and
vegetables suitable for machine processing,
strict compliance with deadlines and agronomic
requirements for the performed technological
operations, taking into account the savings of
energy and resources when using mobile
technology. In addition to the modernization of
the machines for efficient operation, it is
necessary to improve also the scheme of
planting of gardens and methods of cultivation,
transfer horticulture to intensive way of
development
One of the promising directions of development of
agriculture of the Russian Federation is to increase
the production, improve the quality and decrease the
cost of potato cultivation. Annual cleaning is one of
the most intense and costly in transport and
technological processes. Potatoes - blending high
culture and very picky about cleaning. The highest
yields and income from potato production get where
embedded technology to optimize energy and labor
costs. The main (though not only) the special
technical means used during machine harvesting
potatoes, are potato harvesters. The main problem
when cleaning is a problem of balancing conflicting
requirements to the process and possibilities of
agricultural machinery. Including increasing the
purity of the tubers in the container with one hand,
minimization of losses and damages of tubers on the
other hand, when the performance of equipment. In
this article we propose a circuit-design solution
separating the working body of the potato harvester
that allow for cleaning to significantly reduce the
amount of traumatized potatoes in the process of
separating soil and vegetable impurities, creating the
preconditions for the elimination of damage to the
tubers on the hard side of the working bodies of
harvesting machines. Informed choice and timely use
of plug-in modules (separating working bodies) in
modern potato harvesting machines at work in
specific climatic conditions allows them to fully
match the list of regulated agronomic requirements.
Thus, the creation of new science-based technical
solutions for a separation of the organs of potato
harvesters is an actual scientific-technical task, which
makes a significant contribution to the development
of the country
At the present time there is a problem in storage
of agriculture machine-tractor park, because when
operating of agricultural machinery parts thereof
are covered by contamination. The most heavily
becomes dirty machinery working in the toughest
conditions. Pollution promotes decrease the
operational reliability, accelerating of corrosion
and aging, reduce the quality of maintenance
service and performance technique. One of the
number of important factors when setting
technique for storage is the clearing of by of
various types pollution, because the during
storage of cleaned surfaces, components and parts
are subjected still greater destruction and
corrosion. Removal of various kinds of pollution
is an important technological process which has a
significant impact on the preservation of
appliances, performance of work, the quality of
the repair and maintenance of cars, culture,
production and human health. The article contains
a classification of contamination depending on the
difficulty of their removal and density, basic
information on techniques and devices for
purification of units and parts of agricultural
machines, as well as on substances used for this.
We have reviewed bombardment of surfaces with
contaminated carbon dioxide ice particles that
leads to its full destruction. We have improved technology and created a universal device and the
experimental plant for cleaning parts and
assemblies prior to storage, which are not only
inferior, but also in the majority superior to
technical and economic performance of existing
analogues
In agriculture the issue of enhancing the
efficiency of operation of internal combustion
engines (ICE), reducing the costs of
maintenance (TO) and repairing (TP) fuel
supply apparatus (TA) using the improvement
of methods and means of diagnosis is a topical
in connection with the aging rolling stock
farming and lack of investment. Analysis of the
known TA diesel engine vehicles systems
showed that the most widespread system is the
divided type with multiplunger high pressure
fuel pump (fuel pump), while the methods of its
diagnosing are laborious, they require partial
disassembly and have insufficient accuracy.
The mathematical models that characterize the
work of a high-pressure fuel pump (fuel pump)
use a large number of parameters that
significantly affect the quality of dynamics of
the change of pressure values of diesel fuel.
However, in the materials of previously
published articles there were no issues
considered assessing the extent of the
quantitative impact, performance and features
change in the sensitivity settings of the
mathematical models on the simulation results,
there are no recommendations on the degree of
sensitivity and importance of each of the
parameters. For a more accurate diagnosis of
the fuel supply apparatus of a diesel engine it is
advisable to use several methods of diagnosing.
The article substantiates development of a
mathematical model of a high-pressure fuel
pump based on the analysis of modern methods
of diagnosing of fuel equipment for autotractor
diesel engines
In the article we have analyzed the results of measurements of pressure of gases in the combustion chamber and the fuel pressure at the inlet injector diesel D-243 at a processing frequency (acoustic and electromagnetic) fuel 17 kHz
The role of transport in agricultural production
is considerable. It is a connecting link in a
single technological chain of the agroindustrial
complex of the country (RF AIC). In
intraeconomic transportation in the RF AIC,
along with cars, we widely use tractors.
Rational application of wheeled tractors in
intraeconomic carriage substantiates the
possibility of their movements both on
asphalted and dirt roads. A specific share of
tractor transport in domestic agriculture
amounts 22-27% of the total transport
transportations and 50-60% of intraeconomic
carriage. There is a high level of the usage of
tractor transport in Western European countries
and in the United States. In farms of leading
Western European countries (Germany, Italy,
France and others.) there is about 70-90% of
intraeconomic carriage performed by tractor
transport. One of the most substantial and
difficult tasks is to fight with damage and losses
of agricultural production, in which a very
responsible role has been assigned to
automobile and tractor transport as an important
link in the AIC. According to the analysis of
materials for the preparation and use of potatoes and apples, more than 15-20% of the products
do not reach the consumer. Low quality of the
use of vehicles during transportation is a
problem. Transport costs in the prime cost of
produced products in rural areas reach 30-40%
or more. Lowering them will further influence
the development of the agroindustrial complex.
Thus, the creation of new of scientifically
grounded decisions in designs of vehicles for
intraeconomic carriage that enhance
preservation and performance of potato
harvesting and apples in the conditions of
Russia's AIC is the actual scientific and
technical task. Its solution makes a significant
contribution to the development of the country,
as well as it contributes to the implementation
of breakeven, competitive manufacture
Engagement of educational services consumers in assessment of educational system activities through development of mechanisms for independent assessment of education quality is an important and urgent issue. The article provides review of methods for assessment of consumer satisfaction with educational programs