Scientific Journal of KubSAU

In this article the basic principles of air-fuel mixture explosions and striking factors, such as air-striking wave, gas streams, splinters, flame heat, light radiation and sharp sounds are observed. The calculation technique of the emergency emission consequences which is for a quantitative estimation of air-striking wave parameters at air-fuel mixture explosions forming in the atmosphere at industrial failures is given. The basic structural elements of calculation algorithm are listed. It is supposed partial depressurization or full destruction of the equipment containing combustible substance in a gaseous or liquid phase, the emission of this substance in the atmosphere, the air-fuel mixture cloud formation, the air-fuel mixture initiation (ignition) and the explosive transformation (deflagration or detonation) in the air-fuel mixture cloud. The technique allows making the approached estimation of air-striking wave various parameters and defining the probable degrees of men defeat and building damage at failures with air-fuel mixture cloud explosions. The given technique is developed in C# language in the integrated environment of software Microsoft VisualStudio 2010 working out. The program fragment in which the calculation of dimensionless Px pressure and dimensionless Ix impulse is given

This article presents main water supply systems and justifies the choice of direct flow of water supply system in the application of regulation of electric drive for pumps, which doesn’t have any tanks to create pressures required for fire-governmental purposes. This avoids interruption in the supply of reserve while water freezing. In the article the substantiation of the necessity of implementation of adaptive algorithm in modern-WIDE frequency converters by a substantiation of the number of stages of ratio control of voltage-frequency mains. It was revealed that the number of degrees of regulation of 10-12 gives optimum. Modern frequency converters allow you to change the regulation law, establishing 3-5 points of regulation. Therefore, the introduction of adaptive algorithm will reduce the power consumption of the electric drive of the pump of the water supply system. The article shows the simulation model of the "the converter frequency-induction motor," plots of the stator current of mains frequency and active power, surface speed and phase current when changing the voltage and frequency of the mains. These dependences confirm to have applicability of adaptive algorithm in the regulation of modern frequency converters with the skalar administration. Simulation model confirms the sub-physical experiments on a real motor and frequency converter with adaptive control algorithm. As a result of the selection of the parameters, we obtain the voltage reduction of the phase current, and reduce electricity consumption by 5-7%

Nowadays on the market, there is a large variety of CAD systems and specialized software; however, to solve effectively research and design problems there remains task of development and implementation of national Russian-language information systems that are compatible with the requirements of Russian regulations to support the design and research of industrial buildings and facilities parameters. Being irrespective of the sizes and structure of the industrial enterprises, there are a number of approved design techniques, including calculations of lighting, heating, ventilation, water supply and so on. To improve the efficiency of the interested experts work on their basis there were developed efficient algorithms as well as information systems and database. In the article there is justified the necessity of the developing information systems and processes of industrial premises designing on the example of lighting calculation. We have highlighted the main ways of increasing project work efficiency of engineering and technical personnel on industrial enterprises. For their practical implementation, there is required proper organization of information flows by creating programs and databases complex. The article includes information about the "Calculation of lighting industrial enterprises" subsystem that is the part of the "Designing of industrial enterprises" information system. We have presented methodology of work with the software product in the mode of calculation of industrial premises lightning with fluorescent lamps using the method of light flux utilization factor

In the article, we have described the main causes of the fuel-air mixtures explosion and such affecting factors as air blast and fragmental fields. Explosions are performed using various sources of energy. The scale of the explosions consequences depends on their detonation power and the environment in which they occur. The range of the affected areas can reach several kilometers. The basic parameter that characterizes the explosives is the maximum pressure. Increasing distance from the explosion, the maximum pressure and pulse decrease and action duration increases. There is presented method, which is developed in Windows-based applications that allows investigate the dependence of the destruction level on the distance and the explosion epicenter. Algorithm of application operation implements automatically filling of the "molar mass of combustible material, g/mol" field depending on the user’s choice of the flammable substance name. After calculating the raw data, the user moves to the calculation of all the parameters and sees the results of the calculation. By default, the calculation results are presented in tabular form. Further, the results of calculation are presented with a graphical representation of data. The developed software can be used in the educational process at studying such disciplines as "Theory of burning and explosion", "The production safety", "Protection in emergency situations", and also be recommended to practical workers in the sphere of labor safety, prediction and assessment of the technological accidents and catastrophes consequences, teachers of this profile disciplines

To solve the problem of reducing the power supply system’s reliability a prompt full-scale diagnostics based on modern methods can help. Inculcation of information systems for the operational diagnostics implementation allows providing the operating personnel with information that enables to predict possible infringements in power transformers work and to prepare in advance an action plan to address them. The paper presents fragments of the developed monitoring system of power transformer using programmable logic controllers. Within the work of the system there were marked such groups of controlled parameters as information about temperature and the cooling system work; magnitude of windings voltage per phase; the windings current values per phase; information about being transmitted and transmitted power; information about the insulation state. There is designed a functional scheme of the system for monitoring the state of the power transformer. There is described a general algorithm of system functioning. There is developed graphical operator interface that allows to monitor the object state and to manage the system state. Using XML markup language there was designed format of data packets. Designed hardware and software package can be used in the educational process, as it allows to improve the quality of students training, to bring them closer to the realities of modern professional activities; in operational activities as complying with the approved domestic calculating methods replacement of foreign software; in science in solving problems of analysis and optimization of operating parameters of power transformers

In this article, we have explained the necessity of creating precise adaptive energy-saving technologies for use on the milk production enterprises. There are defined the main problems that reduce the enterprises efficiency and milk quality. Many of these problems can be solved if there is organized correctly the information flow through the creation of complex programs and databases. Regardless to the size and structure of the milk production enterprises, they have the following main information streams: animal productivity data; information about the herd composition and structure; information about the diet composition; information about the quality of milk and others. For the storage of this information there is a developed database consisting of 66 tables and 10 diagrams. The article includes information on some charts. To meet the challenges of manufacturing processes modeling there was offered a bunch of "Mathematical package - Database Management System." Within the developed automated enterprise management system we have selected MATLAB and MS SQL Server. There are presented models of thermal balance; heat generated by animals; heat loss from the feed coming from outside and so on. We have also grounded the applicability of the structural processes modeling in conjunction with the possibilities of modern database management system that allows you to convert a wide range of energy saving tasks to automated analysis and forecasting. This approach has the modularity and implementation ease, all of which allows you to build complex information systems, which at the same time are easy to change, expand and renovate