In agriculture the issue of enhancing the
efficiency of operation of internal combustion
engines (ICE), reducing the costs of
maintenance (TO) and repairing (TP) fuel
supply apparatus (TA) using the improvement
of methods and means of diagnosis is a topical
in connection with the aging rolling stock
farming and lack of investment. Analysis of the
known TA diesel engine vehicles systems
showed that the most widespread system is the
divided type with multiplunger high pressure
fuel pump (fuel pump), while the methods of its
diagnosing are laborious, they require partial
disassembly and have insufficient accuracy.
The mathematical models that characterize the
work of a high-pressure fuel pump (fuel pump)
use a large number of parameters that
significantly affect the quality of dynamics of
the change of pressure values of diesel fuel.
However, in the materials of previously
published articles there were no issues
considered assessing the extent of the
quantitative impact, performance and features
change in the sensitivity settings of the
mathematical models on the simulation results,
there are no recommendations on the degree of
sensitivity and importance of each of the
parameters. For a more accurate diagnosis of
the fuel supply apparatus of a diesel engine it is
advisable to use several methods of diagnosing.
The article substantiates development of a
mathematical model of a high-pressure fuel
pump based on the analysis of modern methods
of diagnosing of fuel equipment for autotractor
diesel engines
The article presents native and foreign bench-top
and board methods to test the automobile break
systems. One can find information about some
native trailer-break stands. We have analyzed their
advantages and drawbacks such as low information
capacity, high diagnostics processing time, low
quality of regulation and maintenance operations
due to big influence of the operator’s experience,
his knowledge and individual characteristics, and
great instability of manual test modes on the results
of the investigations. To remove these shortcomings
they have had some experiments at MADI in order
to develop the module to the brake qualities stand.
When using it one can have automatic diagnoses
and flow chart is presented in the article. Due to the
existing vehicles’ state inspection mode and
diagnostic means in our country there appeared new
stands for brakes control. One can attribute to these
devices a range of brake qualities stands developed
and produced at Novgorod plant GARO. These are
STS-3, STS-10 and STO series stands for cars,
trucks, buses and micro-buses. The article also
presents some foreign stands used in Russia such as
universal brake stands STM by META firm, the
break stand IW7 Eurosystem by MAHARUSSIA
firm. We have presented in the article the results of
the analysis of simple and complicated board means
of diagnosis as “Eftor-2”, “Effect”
Based on the analysis of domestic and foreign scientific and patent literature, possible options to reduce weight of electro technical steel in magnetic circuits of electrical machines are explored. A search for the best options for the manufacture of magnetic induction motors stators technology aimed at improving the utilization of electrical steel and improving the energy performance of electric machines is carried out. All the variants are described and illustrated in detail in the drawings. It is pointed out the advantages and disadvantages of each method of manufacturing magnetic wires and the reasons why certain suggestions of technology of manufacturing magnetic circuits have not been implemented in mass production. The main indicators characterizing the manufacturability of constructive decisions are recommended. Economic indicators have been put in the basis of the choice of the optimal variant while designing the electrical machine. An optimal variant should be considered the variant in which all the technical requirements at lowest total cost are met. The latter should be understood not only the cost of materials and machine manufacturers, but also the cost of operation. The dependence of the energy performance of motors with modular designs of stators from the manufacturing technology is pointed out. The existing technology of the most mass electric motors series production, the following disadvantages are typical: low coefficient of utilization of electro technical steel; high specific material capacity, the cost of technology and labor intensity of production; low labour productivity and level of automation of technological process. Due to the fact that the possibilities of increasing of the machines’ specific weight characteristics due to the usage of new magnetic and dielectric materials are exhausted, it is advisable to change the technology of electric motors production, moving away from the traditional design
The analysis of information security tools and systems is carried out in this article. This analysis revealed that the functioning of many of them associated with the implementation of intensive logical calculations. Ways of representing Boolean functions are analyzed, the criteria of efficiency and ways to increase productivity tools and security systems are presented
The article analyzes the state of the dairy industry at the present stage. The efficiency of using concen-trates of melons in the production of multicom-ponent dairy dessert has been proved. The positive influence of concentrates tested on the structural and mechanical properties of jelly dessert, organoleptic and nutritional value of the product has been shown. We have also revealed the reduction in the concentration of the gelling agent in jelly
Results of experimental researches of determination
of corn stems rolling speed in different places of
corn- harvester rolls have been shown. Opportunity
of corn-harvester work under speed of 12-15 km/h
and increased frequency of rolls rotation was analyzed.
Available corn-harvester working regime with regard of intensification of harvesting process was chosen in the result of theoretical and experimental researches.
The article presents analysis of emissions to the
atmosphere in the regions of the North Caucasus
Federal District by means of visualization tools of
Tableau Public 9.0 in order to identify problem
areas and to support management decisions
The possibility of using involute sprockets, more technologically advanced in manufacturing, compared with sprockets with straight, convex-concave profile of the lug on the criterion shock resistance circuit, the maximum permissible speed of the drive sprocket for bush roller chain drives and gears with a toothed chain. The comparative analysis of researches of operation of roller and tooth chain gearings with various steps and types of profiles of sprockets showed that in all cases with increase in a step of a chain the coefficient of speed of blow increases, and the increase in number of lugs at sprockets reduces the speed of blow of the hinge about sprockets tooth. Value of coefficient of speed of blow for couple an evolvent sprockets - a gear chain is much less than value of coefficient of speed of blow for couple a plug-roller chain –sprockets of any profile. Less noise during the work of tooth chain gearings is due to evolvent sprockets. As a result of researches it is established that on kinetic energy of impact of sprockets and the hinge of a chain, sprockets with an evolvent profile can be applied on an equal basis with the sprockets having concave-convex or rectilinear profiles of lugs. Respectively, evolvent sprockets can be used both in chain transfers with roller and with gear chains
The railroad warehouse has most important role in the delivery process of fertilizers to agricultural consumers. It acts as logistics intermediaries. The analysis of material flows has been done on the example of a typical provider of mineral fertilizers in the South of the Rostov region (CJSC «Zernogradagrohimservis») for the last 6 years. Income values and implementation values are varied during the year synchronously for all fertilizers types with the exception of a few months at the beginning and the end of the year. During most of the year the enterprise operates as a negotiable warehouse. In January-February and October-December ammonium nitrate accumulates as a seasonal inventory for the spring peak of implementation, in the rest of the year its reserves are insurance. Stocks of other fertilizers types are insurance stocks for most of the year, in May-July occurs a slight accumulation of their seasonal stocks. A significant portion of mineral fertilizers (especially ammonium nitrate) is delivered for small enterprises and individual farms by cars of this provider. According to the supply contracts, a one-car-run is performed for the vast majority of customers. Routes of delivery of fertilizers are either radial or pendulum (with reverse idle mileage). Therefore, the optimization of the delivery of fertilizers does not seem possible by methods such as obtaining the shortest route network, consolidation of suppliers for consumers, etc.
The article reviews the results of the analysis of technical and operational characteristics of domestic and foreign grill apparatus. The most important indicators of the apparatus are discussed